Getting StartedPorts and Network Requirements

Ports and Network Requirements

This page lists every network port a data source needs in UTMStack v12: from agents and collectors to the UTMStack server, from devices to the UTMStack Forwarder, and from the UTMStack server to cloud services.

Agents and collectors to the UTMStack server

Every agent and collector talks to the UTMStack server on 443/TCP only. This covers registration, the log stream, heartbeats, remote commands and the download of installers and updates from https://<server>/private/dependencies/....

FromToPort
Windows, Linux and macOS agentsUTMStack server443/TCP
UTMStack Forwarder (the "Collector")UTMStack server443/TCP
IBM AS/400 CollectorUTMStack server443/TCP
UTMStack self-monitoring collectorUTMStack server (it runs on the same host)443/TCP

The install commands check that the server answers on 443 before they register anything. If the check fails, open 443 between the host and the server and run the command again.

Agents and collectors need a direct connection: they have no proxy setting, and the install check opens a plain TCP connection to the server. If your hosts can only reach the internet through a proxy, allow direct traffic from them to the UTMStack server on 443.

UTMStack v11 agents used ports 9000, 9001 and 50051. UTMStack v12 does not use or publish these ports. If your firewall rules still allow them for UTMStack, you can remove those rules.

Devices to the UTMStack Forwarder

Devices send their logs to the host where the UTMStack Forwarder runs, not to the agent. Open these ports inbound on the Forwarder host and on any firewall between the device and that host. Open only the ones you use.

SourceData typePort on the Forwarder
Cisco ASAfirewall-cisco-asa514/UDP, 1470/TCP
Cisco Firepowerfirewall-cisco-firepower514/UDP, 1470/TCP
Cisco Merakifirewall-meraki514/UDP, 1470/TCP
Cisco Switchcisco-switch514/UDP, 1470/TCP
VMware ESXivmware-esxi7002/UDP, 7002/TCP
ESET PROTECTantivirus-esmc-eset7003/UDP, 7003/TCP
Kaspersky Security Centerantivirus-kaspersky7004/UDP, 7004/TCP
Fortinet FortiGatefirewall-fortigate-traffic7005/UDP, 7005/TCP
Palo Alto Networksfirewall-paloalto7006/UDP, 7006/TCP
MikroTikfirewall-mikrotik7007/UDP, 7007/TCP
Sophos Firewall (XG)firewall-sophos-xg7008/UDP, 7008/TCP
SonicWallfirewall-sonicwall7009/UDP, 7009/TCP
Deceptive Bytesdeceptive-bytes7010/UDP, 7010/TCP
SentinelOneantivirus-sentinel-one7012/UDP, 7012/TCP
Generic syslog, CEF and LEEFsyslog7014/UDP, 7014/TCP
IBM AIXibm-aix7016/UDP, 7016/TCP
pfSensefirewall-pfsense7017/UDP, 7017/TCP
Fortinet FortiWebfirewall-fortiweb7018/UDP, 7018/TCP
Suricatasuricata7019/UDP, 7019/TCP
GitHub webhooksgithub7020/TCP (HTTPS)
Oracle Databaseoracle7021/UDP, 7021/TCP
NetFlow exportersnetflow2055/UDP (UDP only)
  • These are the default ports. To use another port for a built-in integration, change it on the Forwarder host with change-port first. See "Use a different port" in UTMStack Forwarder.

  • The four Cisco integrations share 514/UDP and 1470/TCP. Only one of them can use a port on one Forwarder, so give the others different ports.

  • TLS is available on every TCP syslog port once a certificate is loaded on the Forwarder. TLS uses the TCP port.

  • Custom integrations and JSON Input use the port you choose when you enable them.

  • GitHub sends from the internet, so port 7020 must be reachable from GitHub. See GitHub.

  • Cloud security consoles that send syslog from the internet (for example some SentinelOne and ESET deployments) need the Forwarder's port reachable from the vendor's addresses. Allow only those addresses.

Windows computers to a Windows event collector

If you use Windows Event Forwarding, the source computers send events to your Windows event collector over WinRM: 5985/TCP (HTTP) or 5986/TCP (HTTPS). This traffic stays between your Windows computers; only the collector's agent talks to UTMStack, on 443.

IBM AS/400 Collector to your AS/400 systems

The AS/400 Collector connects out to each AS/400 (IBM i) system you list in its configuration file. The host where it runs needs network access to those systems. See IBM AS/400 (IBM i) Collector.

UTMStack server to cloud services

Plugin integrations are pulled by the UTMStack server itself, so the server needs outbound HTTPS to the services you connect:

IntegrationOutbound HTTPS to
AWS CloudWatchAmazon Web Services APIs
Microsoft AzureAzure Event Hubs and Azure Storage
Google CloudGoogle Pub/Sub
Microsoft 365 and Microsoft 365 through Microsoft Graphlogin.microsoftonline.com, manage.office.com, graph.microsoft.com, and the matching .us endpoints for government clouds
CrowdStrike FalconThe CrowdStrike API of your cloud region
Sophos Centralid.sophos.com, api.central.sophos.com

Ports on the UTMStack server itself

For the ports analysts and administrators use (80, 443, Cockpit on 9090) and the ports you must block from outside (for example 10001), see Network Ports and Firewall.

Multi-tenant installations

With the multi-tenant licence, install commands copied inside a child tenant use that tenant's domain as the server address. Make sure that name resolves from your hosts and that 443 is open to it.